How to make a feeder from a bottle 1.5. Feeder from a plastic bottle: the best ideas and options for creation and placement (75 photos). Plastic house in the form of a bunker

A feeder is a very simple device, but very necessary in any period of winter, because at this time birds need food, which is very difficult for them to find on their own. Therefore, you can make a feeder from a 5-liter plastic bottle, which will have a simple design, but can provide food for a large number of birds.

Advantages of a plastic bottle

Feeders can be made from a variety of materials. Plastic containers are the most popular in this regard, as they have many advantages. These include:

• availability;
• low cost;
• ease of processing;
• the ability to protect feed from wind and precipitation;
• resistance to temperature changes.

As for plastic containers with a volume of 5 liters, they are especially popular in the manufacture of feeders. This is due to the fact that she:

• has a wider bottom that can accommodate more birds;
• It has good capacity, which means you can add more feed at a time.

Tools and materials

To make a feeder from a 5L bottle, you don’t need an expensive tool. A complete design for birds can be made using:

• bottle;
• rope or wire;
• stationery knife and scissors;
• awl;
• tape or tape.

Step-by-step manufacturing instructions

A large number of different feeders can be made from a 5 liter plastic bottle. It can be horizontal or vertical, with or without a lid. It is also possible to manufacture a product with automatic feed supply.

Horizontal design

The horizontal design allows you to feed a large number of birds. In addition, it is easy to manufacture. To build the product, you need:

If you take bottles of different colors for such a product, then it can become a decoration for your personal plot.

Simple execution

Sometimes there is no time to make a feeder of a complex design or you need to make several of them in a short period of time. For such situations, there are two options for the simplest designs from a 5 liter bottle. The first option is as follows:

1. You need to make a wide hole at a distance of 4-5 cm from the bottom. It is recommended to seal the edges of the hole with electrical tape to eliminate the risk of injury to the birds.
2. Place any dense material (for example, plywood or tiles) at the bottom of the bottle. This measure is needed for weighting.
3. You need to tie a wire or rope to the neck, using which you can hang the structure on a branch.

The second option involves a horizontal placement of the feeder, which makes the design even simpler. All you need to prepare in advance is a bottle, wire and a knife. After that:

1. Cut off the bottom and neck.
2. Place the bottle on its side. Make two holes in the upper part through which string a rope or wire. Hang the feeder on a branch using the loop formed.

Winter structure with roof

From a 5 liter plastic bottle you can make a so-called proper winter feeder. It will have a roof to protect the feed from snow and water, high walls to prevent the wind from blowing the feed out, and good fastening to hold the structure to the tree.

To make such a feeder, you need to prepare one large bottle and two 1.5 liter containers. No special devices are required. The manufacturing process is carried out according to the following plan:

With the onset of cold weather and frosty days, it is necessary to understand that birds cannot always get food in difficult times. It is a person’s conscience, therefore, along with the instructions from the site, a bird feeder made from a plastic bottle should appear in the yard.

Read in the article

Tips and tricks for making your own feeders from plastic bottles

Making a dining room for feeding birds from available plastic is not as long a process as creating the same feeder, but from wood. The principles of working with bottles are the same, only the methods are different.

The work requires sharp scissors; you can use a pair: large and small. Large ones are convenient for cutting, and small ones make cuts. In addition to scissors, other materials and components are needed, depending on the type of craft: wooden spoons, pallets, rope, saucer, decorative elements.

How to make a horizontal feeder from a plastic bottle

A good option is horizontal from a bottle.

A horizontal kitchen for birds is created as follows.

1. The five-liter bottle should be placed on its side: rectangles are drawn on the parallel sides with a felt-tip pen. First, cut through the bottom and sides of the rectangles.
2. Now we bend the resulting caps upward. If you go along the fold line with pliers, you will get an excellent visor. Pichugi will hide under it from the wind or snowstorm.
3. In the lower part you can make two holes opposite each other. A perching stick is inserted through the holes.
4. Despite the fact that the feeder is covered, rain can enter it from the sides. Therefore, several small holes are pierced at the bottom - through them the water will drain without spoiling the food.

Interesting feeder made from a plastic bottle and wooden spoons

To make a feeder with wooden spoons, you don’t have to look for a five-liter bottle. A very small one will do. In addition to the container, you need two wooden spoons with long handles. These spoons are usually used to take samples from dishes. Don't forget to prepare some wire.

The procedure is as follows.

1. You need to step back a little from the bottom (8–10 cm is enough).
2. Two holes are made parallel to each other. The handle of one spoon should easily pass through them.
3. You need to step up again by 7–10 cm.
4. The same holes are made here, but on other sides of the bottle.
5. You also need to pass the handle of the second spoon through the holes made. As a result, the spoons will be located perpendicular to each other in the same plane.
6. To make the food fall out onto the spoons more easily, it is better to make larger holes on the wide sides.

This type of feeder can also be made from a 5-liter plastic bottle, but for large containers it is better to leave other methods for creating a bird kitchen.

Two Bottle Hopper Bird Feeder

To create a bunker bird cafe you will need two 1.5 liter bottles.

First, you need to cut two round holes in one bottle. They should be located approximately 7–8 cm from the bottom. The second bottle must be turned and inserted into the hole. That is why it is not recommended to make too large slots at first: the inserted container should not swing freely. If everything is assembled correctly, the neck will not reach the bottom completely. You can add grain!

The product is hung with ropes or installed between strong branches, slightly squeezing the bottles.

To make the last option, as in the photo above, you will need five-liter and one-and-a-half liter bottles. The neck of a smaller bottle is removed. It is calculated so that the bottom of a 0.5-liter bottle stands at the bottom of a 5-liter bottle, and the upper part rests against the neck of a larger bottle.

To allow birds to get inside, large windows are cut on the sides of the five-liter container.

Small holes are made in the lower part of the smaller container - through them the food will be poured into the feeder. The product is filled as follows: open the lid of a 5-liter container and fill the smaller container with food. It spills out through the holes, filling the bottom of a larger container. As soon as the food becomes smaller, he will add it himself.

Advice! Those who want to see the process better should take bottles that are contrasting in color: the inner one should be darker than the outer one.

Ways to decorate plastic bird feeders

Creativity is good everywhere. A bright and interesting craft in appearance will decorate, attract attention and simply please the eye.

Where are bird feeders placed?

There are few rules for placement: the product should be out of reach of predators and hang on strong branches. If possible, the branches should not only hold the feeder, but also protect it from swaying in the wind. Also in the future

In winter, birds that have not flown south need human support. Realizing this, concerned citizens are interested in using the bottle to place it in the park or near their home. The manufacture of such a device can be greatly simplified if you take some unnecessary container as a basis.

meets the following requirements:

1. the food is protected from precipitation. Otherwise, it rots and becomes moldy, and in winter it freezes;
2. there are perches that make using the feeder convenient;
3. The material of the feeder is moisture resistant;
4. Several holes were made in the walls, located in pairs opposite each other. Birds will not dare to enter a closed room with only one entrance;
5. the edges of the entrance holes are sealed with tape or tape: thin, hard plastic injures birds;
6. A weight is provided to keep the feeder from swaying in the wind.

The simplest option

A plastic bottle is an almost ready-made feeder, only minor modifications are required:

1. one large opening (1.5 liter bottle) or several smaller ones and opposite each other (5 liter bottle) are cut out in the wall at a distance of 7 cm from the bottom;
2. The sharp edges of the openings are covered with electrical tape or tape;
3. several holes are made in the bottom to drain moisture;
4. two holes are pierced in the lid with a heated nail and a cord is threaded through them for hanging on a branch and a wire for placing unsalted lard inside the feeder.

The feeder is ready, all that remains is to hang it in a place inaccessible to cats and other predators. If it’s windy there, put a bag of sand or earth at the bottom.

The simplest feeder has a number of disadvantages:

• moisture and dirt get into the feed;
• difficulty of maintenance: you often have to change the food due to spoilage or constantly add a little bit of it;
• the contents are accessible to large birds and they do not allow small ones to feed.

A 5 liter bottle can also be placed horizontally - this allows more birds to feed at the same time.

Feeder with dispenser

In this option, also called a bunker feeder, the disadvantages of the previous solution are eliminated. The device is assembled from two identical bottles with a volume of 1.5–2 liters.

Procedure:

1. one bottle is cut from the bottom to a length of 4–6 cm;
2. the second - from the side of the neck for a length of 7–11 cm. The exact length is in paragraphs. 1 and 2 depend on the type of bottle and are selected experimentally;
3. The first bottle is inserted into the second so that its neck is directed towards the bottom and is located at a distance of 30–40 mm from it. This bottle is a bunker: it contains a supply of food, part of which is poured through the neck into the bottom of the second bottle. The spilled grains block the neck, and when the birds peck them, a new portion is added;
4. Both bottles are held together with hot glue. If the first bottle itself fits tightly enough into the second, this step is skipped;
5. the protruding part of the first bottle (without the bottom) is opened with longitudinal cuts into “petals” 2–3 cm long and 1–2 cm wide. This is necessary for installing protection against getting wet;
6. On the second bottle (with a bottom), with a marker or felt-tip pen, draw the outlines of the openings for access to the food. The lower edge of the opening is located at the level of the edge of the neck of the hopper bottle or slightly above it. At a lower position, the grain will spill out of the feeder;
7. Openings are cut out using scissors along the drawn lines. The edges of the openings are covered with electrical tape or tape.

The following feeders also performed well:

1. a 1.5 or 2 liter bottle is pierced through just above the bottom;
2. insert the handle of a wooden spoon into the holes so that the scoop fits tightly to the bottle;
3. similarly, just above the first spoon and perpendicular to it, the second one is installed;
4. small openings are made in the bottle above the scoops of the spoons;
5. a visor is made from the top of a 20-liter bottle: a hole is cut in the center for putting on the feeder;
6. Holes are made in the lid and a cord is threaded for hanging.

The bottle is filled with food and part of it spills into the spoons through the holes made. As the birds consume the food, it will be added again and again.

A multi-user feeder with a dispenser is made as follows:

1. prepare a 1 liter plastic bottle and an old thick plastic bowl;
2. several holes are made in the bottle at such a height that, after placing it in a bowl, they are slightly below its sides;
3. coat the bottom of the bottle with “liquid nails” or other reliable glue and place it in a bowl;
4. attach twine to the lid for hanging.

The bottle is filled with food and hung in a convenient place. Some of the contents are constantly poured into the bowl, and at the same time it plays the role of a perch for several birds.

Tit feeder

Tits are the most vulnerable part of the feathered community left to winter at home; these birds are characterized by:

• small sizes. Because of this, tits are easily pushed away from the feeder by pigeons and other large birds;
• caution towards people. These birds do not risk coming close to a person and briskly begging for food from him, as pigeons and sparrows do;
• non-aggressive nature. Tits do not defend their rights even in fights with an opponent of the same weight category. They are mainly offended by sparrows: they resolutely seize the feeders and, in the most severe form, do not allow the tits to feed there. Such a bird will yield to a small nosy nuthatch.

The proposed feeder solves the problem: for large birds it is small, for sparrows it is frighteningly intricate, it is done like this:

1. prepare a 1-liter plastic bottle and a cardboard tube from a package with cling film or baking foil (a roll is wound on it). A narrow tube is not suitable, the minimum diameter is 3.5 cm;
2. Two holes are cut in the bottle just above the bottom, one opposite the other, so that the tube can be pierced right through the bottle. It is important to guess the diameter of the hole so that the tube in it does not deform, but fits tightly;
3. an oblong hole up to 1 cm wide is cut out in the middle of the tube with a knife;
4. pass the tube through the bottle, turning the oblong hole down;
5. pierce the bottle right through just below the tube, with a branch as thick as a pencil - these are the perches;
6. holes are pierced in the lid and a wire or cord is threaded for hanging.

Tit feeder

After unscrewing the lid, the feeder is filled with grain, closed again and hung. Clever tits guess to look into the tube and take food from the cut, while to sparrows this device seems mysterious and incomprehensible.

The feeder works according to the “bunker” principle: the grain gradually settles and as long as its level remains above the cut, there will be something to profit from in the latter.

Protection against wet feed

If the feeder is supposed to be hung in a place open to the winds, protection from getting wet is made from a 5 liter bottle:

1. on the side wall, 2 cm from the bottom, a line is drawn parallel to it;
2. make an incision along the drawn line, and then perpendicular to it and in the direction from the bottom - two more. The cuts form an inverted letter “P” and limit the opening of such dimensions that the feeder with the dispenser goes inside (the “petals” cut in the upper part simplify installation);
3. The feeder is placed through the opening into a 5-liter bottle and placed on its bottom. If it is too big, the bottle-hopper is trimmed;
4. a self-tapping screw is screwed through the bottoms of both parts, holding them together;
5. the valve covering the U-shaped opening in a large bottle is cut to a length of 2–3 cm and bent upward, forming a visor. This is protection from precipitation;
6. on the opposite side of the body there is a similar opening with a visor, but smaller in size - about the size of a bird for which the feeder is intended;
7. The neck cut off during the manufacture of a feeder with a dispenser is adapted under a funnel for loading grain into the hopper. To prevent it from getting lost, it is tied to the neck of a large bottle with twine or wire;
8. several holes are drilled in the bottom of a large container to drain condensate and wind-blown rain moisture;
9. two holes are pierced in the cap of a 5-liter bottle and a wire or cord is passed through them for hanging;
10. To prevent the feeder from swaying in the wind, hang a weight from below on a fishing line or tie it to a branch below.

If the location of the feeder is protected from the wind, instead of a “room” made from a 5 liter bottle, it is enough to use a canopy made from the top part of a 20 liter bottle. The feeder is attached to it from below by the “petals” by gluing with “liquid nails” or mechanically (with bolts or self-tapping screws).

perch

A long branch as thick as a pencil is used to pierce the feeder right through. Its ends protruding from both sides will become perches, providing the birds with a comfortable landing.

Holes for the perch are cut at a distance of 40 mm from the bottom of the feeder. Their diameter should ensure a tight fit of the rod. Otherwise, the food will spill through them.

Instead of a branch you can use:

• simple pencils;
• durable chopsticks;
• wire, etc.

To increase the number of “seats”, additional perches are installed. They are placed 50-70 mm above the main ones and at an angle to the latter.

For reliability, the rods are fixed with glue. At the same time, it will act as a sealant, preventing water from seeping through the gaps.

Which food is best?

Different types of food are characterized as follows:

1. raw sunflower seeds, pumpkin seeds, watermelon seeds. The best food for birds. They also eat fried seeds, but raw ones are healthier;
2. millet. Some birds, such as parrots, eat millet with pleasure. But some ornithologists consider this food unsuitable. Millet is millet without shell. And without it, fats oxidize on the surface of the grains and toxic substances are formed, pathogenic microbes multiply. Tits do not touch millet, at least if there is a feeder with seeds nearby.

Birds eat bread crumbs, but such food is undesirable for a number of reasons:

• harms the body due to the presence of yeast: putrefactive processes develop in the beak, intestinal microflora is disrupted;
• quickly becomes moldy due to insufficient sanitary control in modern bakeries (infected by mold fungi);
• stale in the cold.

Video on the topic

How to make a feeder from a 5 liter plastic bottle:

There are countless options for bird feeders made from plastic bottles. Authors who are inclined towards artistic delights turn their crafts into real works of art. For example, a feeder wrapped in glued rope and decorated with pine cones looks attractive.

You just need to remember that a feeder with an overly saturated design will seem suspicious to the birds and they will be careful about approaching it. It is recommended to leave a window in the decoration of the bunker feeder to control the feed level. Don’t neglect the help of children: their wild imagination will help give a boring craft a unique look.

Making a plastic bottle bird feeder for your backyard and garden is fun and quite easy. There are many ideas with which you can build something useful from such waste and add some uniqueness to your summer cottage. These bottle crafts will help feed your backyard feathered friends and keep them from starving during the cold winter months.

There are many amazing ideas for making crafts by upcycling. Bird feeders made from a 5-liter plastic bottle are a great example of this. Just consider a few inspiring designs that can be put into practice.

To make a plastic bottle feeder, rinse the containers thoroughly and let them dry completely. It is very important to dry empty items well, otherwise the birdseed will stick to the walls and spoil. Choose any 5 quart plastic bottle bird feeder design idea and turn that junk into unique and beautiful yard decorations and useful bird supplies.

Big feeder

A variety of feeder models demonstrate how to reuse plastic bottles. The main thing is to create a roof and a place for the birds to eat and shelter from the snow. To do this, you need to make 2 holes through the top of the container, stretch a cord or wire through them so that you can hang the structure. A bird feeder can also be nailed to a wooden post, fence or wall outdoors. It should be placed in a place where birds can eat in peace without disturbing other small animals, such as squirrels.

If desired, the craft is decorated using unnecessary wooden parts, decorative rope or tree bark. Even a schoolchild can make a bird feeder from a bottle. You just need to follow the step-by-step manufacturing instructions:

Keep in mind that the size of the feeder must be suitable for specific birds. The food also needs to be selected appropriately: sunflower seeds will attract tits, while mixtures containing millet and other small seeds will lure sparrows and finches. If you use a heavy plastic container (such as a large water bottle) to make it, you can fill it with corn and peanuts, which are happily eaten by magpies and woodpeckers.

Children will watch with interest as the birds eat from the feeder. This is a great fall activity for the whole family and a fun weekend activity for people of all ages.

Using small containers

To make a bottle feeder, it is not necessary to use 5-liter containers. Even the most common ones from soda will come in handy. What you will need for this:

When all the necessary materials, tools and materials have been collected, you can begin making the feeder . Step-by-step master class:

1. Dry the container and lid. Using a knife, cut a circle of plastic on one side of the feeder, approximately 3 cm in diameter. This hole should be 3–5 cm above the bottom.
2. Then cut a hole directly below the feeding hole. Insert a pencil or skewer through it until it stops at the back of the container. Make 4 of these bird perches. They can be secured with glue.
3. Cut a cord about 50 cm long. Tie one end to the washer and pass the free end through the bottom of the plastic container and then through the top of its lid. Close the cap tightly and tie a knot at the top.
4. Pour bird feed into the bottom of the container through the hole you made, then hang the feeder near a window or on a tree branch and you'll soon have feathered visitors!

Don't forget to replenish the feeder with grain, as the local birds will now depend on you as a food source.

Another craft idea

This process of making a feeder takes about 30 minutes. All you need is ordinary household waste and basic skills. You will need the following materials:

Cut off the bottom 2 inches of the soda bottle, then cut four slits around the edge of the top so you can fit the bottom on top. Then cut four small holes/slots in the top of the bottle to allow access to the food.

Cut out the top of the milk bottle (where the sides start to taper towards the spout), leaving some plastic for the handles. Then make three holes around the new piece, evenly spaced, not too close to the edge. Make sure your holes are small enough to hold the hanging pieces.

If you are using a bicycle tube, cut a piece about 90cm long, then cut it so you have a long rectangle of rubber. Now cut three strips along the entire length, about 0.5 cm wide. You will use these to hang the feeder. Then you can start assembling.

Attach the bottom of the soda bottle to the top (this will be the cap you open to add bird food). Do not seal too tightly, just enough so that a bird, squirrel or strong wind does not open the lid. Now insert the rubber strips through the holes in the milk bottle and tie a large knot on the other side. When using rubber, almost any assembly must be thick enough. Make sure it doesn't come undone.

Slide the milk bottle piece over the bottle cap. To prevent the feed from flowing, you will need to tighten the strips on it by tying a small ring of rubber around the three lines. To fill the feeder, this ring simply slides up and the lid opens.

Creating a bird feeder

With the arrival of autumn, children at school are given tasks to make some crafts. A bird feeder is the perfect solution. For this you will need:

When the materials are ready, you can begin manufacturing. To do this, you must follow a certain sequence:

1. Cut a hole in the back of the bottle, making it large enough for the bird to fit inside.
2. Make two small holes near the top of the container to attach garden wire so you can hang the feeder.
3. Use a marker for decoration.
4. Fill the feeder with bird food.

Remember that you need to make a small drainage hole at the base of the bottle, otherwise the birdseed will be constantly soggy and sour.

Master class on making a drinking bowl

From a five-liter or smaller container you can make not only a feeder, but also a drinking bowl for your feathered friends. Necessary tools and materials for this:

Almost all materials and tools can be found at home in the garage or bought in a specialty store, and bird food is sold on the market.

Take a bottle cap and mark the lines as if you were cutting a pie. Draw lines along the top sides of the lid where the holes will be. Place the cable ties (indicated in red) on the bottom of the bottle cap so that they extend from the middle of the “doors”, outline them with a marker. Place a dot where the hole for the cable tie is. Where the cable exits, cut off the other end on the side of the cover.

Cut off the sides of the lid and then cut off half of the cut part to give the birds access to the food. Bend it a little. Remove the inner ring to allow the cable to pass through the bottom.

Screw the cap onto the bottle and remove the cap. Make 4 vertical cuts and use a knife to remove all burrs.

Slide the cable tie into the bottom slot and remove the side slot. Attach the cable bundles. Repeat the same step for the second cable bundle.

Cut the wire to length. It will depend on the size of the container you use. For a small bottle with a recess around the middle, place a “collar” there. For a larger bottle, 1–2 liters, a “collar” is made from wire. Add extra wire around the "top".

Take 3 wires, make a small loop at one end and thread the wire through them. Wrap the "collar" wire around the bottle, moving the other wires until they are evenly distributed around the bottle. Pull the wires up and weave them together to form a hook.

Place the bird food in the bottle, screw on the cap (this may take some effort), and hang the finished bird feeder where your birds can see it.

Teach your friends how to use discarded plastic containers to make simple DIY bird feeders that help keep winter birds well-fed, healthy and happy. This is a nice gesture that shows a friendly attitude towards the environment and wildlife.

Birds living in the wild need protection and care. It is especially difficult for them during winter: when it is frosty outside, it is so difficult to find shelter and food.

That is why caring people try to feed our younger “brothers” as much as possible. One of the ways that will not only help birds, but also decorate your garden is a feeder made from scrap materials.

In this article we have collected several of the most affordable options - based on descriptions and photographs, using already unnecessary items (plastic bottles or old dishes), you can easily arrange a place where flocks of birds will gather.

Material selection

After assessing the resources you have to create a feeder, you can choose an idea you like. However, it is worth remembering that not only its appearance, but also practical characteristics such as stability depend on the configuration.

That is why a good feeder must meet the following requirements:

Wear resistance and durability. Preference should be given to wood or plastic, which can withstand weather conditions without getting wet from rain and snow, or collapsing under gusts of wind.

In addition, the birds themselves often cause damage to the feeder - in search of crumbs, their beaks and claws scratch and tear fragile materials.

Proper size. Remember that if you cut out a small feeder, for example, from tetrapack, then large birds will not be able to eat from it, and small ones will start fights for space and shake out the food on the ground.

No sharp edges, protruding nails, etc. Birds are very delicate creatures, their feather protection and the skin on their legs cannot prevent cuts from sharp objects, so make sure that your feeder is not dangerous for them, especially if it is made of glass, plastic or planks!

Location and installation

Choosing the right location is extremely important!

Having chosen the most suitable position from the point of view of landscape design, evaluate:

Accessibility for birds. Perhaps the feeder will be closed from them by thick branches, or, conversely, it will be too open, and then, in a strong wind, the birds simply will not be able to get close to it.

Difficulty for cats. These animals are excellent hunters, especially those who live in villages and holiday villages. They are stronger, faster and more dexterous than their domestic counterparts, and therefore, sneaking up to the feeder, they can cause great damage to the bird community.

Ideas for making your own feeder

There are a huge number of different types of feeders - it all depends on your imagination and available materials.

We will try to consider both the simplest and the most original ideas.

House made of wood or plywood

Despite the apparent complexity, such a structure can be assembled with unnecessary boards, pieces of wood, glazing beads, plywood and, of course, special glue or nails.

Note!

The base should be a heavy, flat board. To make the walls and roof, you may need a drawing, however, you can get by with an eye.

A wooden bird feeder, depending on how much attention you pay to it, can become not only a place for birds to feed, but also an elegant decoration for your garden.

Feeder made from plastic bottles

This type of feeder is very easy to make and is perfect if you decide to involve children in the creation process. You need to cut one or two holes in the bottle so that you can not only pour in the food, but also access it without difficulty.

Of course, you should try to ensure that the cut edges come out neat and not too sharp (in addition, it is advisable to cover them with tape).

If you are using a small bottle (1.5-2 liters), then you can do it in two ways: cut a square or rectangular hole in the bottle, or prefer a U-shape so that you can bend a piece of plastic and make a visor.

If you decide to use a large bottle (5-6 liters, in which drinking water is usually sold), you can make a large side cutout. This will not only provide more food, but also give the birds room to maneuver.

Note!

To prevent the wind from ruffling a light bottle, it is worth placing a stone or a piece of brick at the bottom. This also applies to the next type of feeder.

Bird feeder made of tetra pack

You can also use juice or wine boxes to make a bird feeder.

To do this, you should follow the same technology as in the previous case: mark the location of the cut, cut it in shape, glue tape (or adhesive tape) along the bottom side of the opening, then make holes for a strong rope in the upper part of the tetra pack. All that remains is to hang the feeder in the place you choose.

Shoe box feeder

The cardboard from which the shoebox is made cannot be considered a durable material, but it is quite resistant to moisture, and if it is frosty outside, such a feeder can hang until spring.

The technology for making the feeder, as in previous cases, is also very simple: make four to six holes for the rope, slits on the sides and put a weight on the bottom for stability.

Note!

Other options

The above options are extremely popular - such feeders can be found at any dacha. If you want to make a unique feeder with your own hands, you should take unusual materials, for example, old tableware: a cup and saucer.

In the autumn, you can cut out a product from a pumpkin or zucchini; in the winter, halves of an orange, peeled from the pulp, are suitable for this. These feeders will surprise your neighbors and will undoubtedly decorate your garden!

Photo of a DIY bird feeder